Marker Batch Commands

Check out the list of batch commands available for automation of various routine tasks in Marker.

Click  a link to view more information about each batch command.

Keywords and text appearing below in square brackets is optional.

 

@!

End of batch-file performing.

Alias: @EOF

 

@EXIT

Stop the batch file execution and close the Marker application.

Alias: EXI

 

@PAUSE

Pauses the batch execution and displays the optional message. Use File>Batch>Continue command to continue the execution of the paused batch file.

Alias: PAU

Keywords:

[/MSG=<message text>]

Optional message.

Using ',' and '>' symbols in the message is prohibited.

 

@SET

Sets preference value stored in the value to OPTITEX.INI file.

Keywords:

/SEC[TION]=<Section name>

 

/KEY[WORD]=<Keyword>

 

/VAL[UE]=<Value>

 

 

@UNIT

Sets working units.

Alias: UNI

Keywords:

/CM

 

/MM

 

/ME[TER]

 

/IN[CH]

 

/FE[ET]

 

/YA[RD]

 

 

@NEW

Closes the current marker file and starts new clean marker.

Keywords:

[/NA[ME]=<title>]

 

 

@OPEN

Opens (or merges) marker files

Alias: OPE

Keywords:

/FI[LE]=<file-name>

Specify the Marker file name to open

[/ME[RGE] = {NO | YES}]

Allows you to merge this marker with the currently opened

 

@SAVE

Saves results in marker file.

Alias: SAV

Keywords:

[/FI[LE]=<file-name>]

The file name used for the file saving.

  • If the file name is specified, the Marker file is saved using the specified name. In a case when the file with the specified name already exists, further behavior is determined according to the /OVERWRITE flag described below.

  • If the file name is not specified by /FILE flag, but the file name was already defined using @NEW command with the /NAME flag, a marker file is stored with the name specified by @NEW command.

  • If the file name is not specified neither by /FILE flag nor by @NEW command, a marker file is stored with the name composed from "backup" word and ---X suffix, where X is a sequential number.

[/OVER[WRITE]={NO | YES}]

Controls over saving files in a case when the file with actual name already exists.

  • When NO option is chosen, in a case when the file with the actual file name (specified by the /FILE flag) already exists, a new file will be stored with the name composed from actual file name and ---X suffix, where X is a sequential number.

  • When Yes option is chosen,  in a case when the file with the actual file name (specified by the /FILE flag) already exists, the file will be overwritten.

[/XM[L]={NO | YES}]

Use XML-style header

[/LO[G]={NO | YES}]

Use Log-file

 [/FO[RMAT]={DSP8 | DSP9 | MRK | MRKML}]

The file format used to write the file

(DSP8 and DSP9 formats are discontinued starting from Optitex 19SP6)

 

@UPDATE

Check Updates Styles changed in PDS.

Alias: UPD

Keywords:

[[/ST[YLE]=<file-name>]

Style file name to be updated

[/FI[LE]=<file-name>]

New file name for update this style (if new file is used and if Style file name is defined)

[/MA[TERIAL]=<material>]

Pieces with the Material name only will be updated

 [/PI[ECE]=<piece name>]  

Pieces with the such names will be updated

 [/CO[DE]=<piece code>]

Pieces with the such codes will be updated

 [/GE[OMETRY = {NO | YES}]

Update only geometric parameters without changing layout on marker

If certain piece is note specified by PIECE or CODE keywords, changes are applied to entire content.

 

@DESIGN

Create the Marker order based on PDS file

Alias: DES

Keywords:

[/FI[LE]=<file-name>]

The name of the style file (PDS)

[/SE[AM]={I[NT] | E[XT] | C[UT] | S[EW] | B[OTH]}]

Select style contours that will participate in order creation

[/OR[DER]=<Order number>]

Specify the order number

[/ST[YLE]=<Style name>]

Specify the style name

[/MA[TERIAL]=<Material>]

Specify style materials to participate in the order

[/SI[ZE]=<size-name>]

Specify the size available within the style

   [/QU[ANTITY]=<No.of sets of the size>]

Specify the bundles quantity required for the current style

   [/RQ=<No. of sets with alternative>]

Specify alternative bundles quantity required for the current style

[/SU[BSTYLE] = <sub style name>]

Specify the name of sub-style

Repeat the /SIZE=... /QUANTITY=... /RQ=... construction for every size to be added to the order.

 

@IMPORT

Open style file (PDS).

Alias: IMP

Keywords:

/FI[LE]=<file-name>

 

 /FO[RMAT]=<file-format>

Following formats are available: DXF, AAMA, ASTM, IGES, CADL(CadKey), DFT(cncKad), GERB(Gerber Cutter), HPGL, DMPL, MIC[ROJET]

[/UN[IT]=<Units>]  

CM, MM, ME[TER], IN[CH], FE[ET], YA[RD]

[/CL[EAR]={NO | YES}]  

Clears marker before import.

[/SI[ZES]={NO | YES}]

"Use Sizes" (as button in Import dialog)

[/DS[N]={NO | YES}]

Saves Design file

[/GB[UF]=<Buffer size>]

Sets Buffer size

[/GB[UF]I[NIT]={Y[ES] | N[O]}

Init Buffer. By Default - YES.

[/GB[UF]T[YPE]={A | C | U | D | L | R | UL | UR | DL | DR |  ULR | DLR | RUD | LUD }

Buffer Type. By Default - A ( Around ).

/GD[IR]=<Rotation allowance>]  

[1(None), 2(PI), 4(PI/2), 8(PI/4), 0(All enable)

[/GM[IR]=<mirror>]  

0(None), 1(Allow by X), 2(Allow by Y)

[/QU[ANTITY]=<Quantity>]

 

[/SC[ALE]=<Scale>]

 

[/NN={NO | YES}]   

Using block number as piece name (Gerber Cutter only)

[/JO[IN]=(NO | YES}]

Checking equivalent pieces after import.

[/MA[TERIAL]=<Material>]

 

[/CD or /CO[DE]=<Code>]

 

[/BO[X] = { YES | NO }]

Import in Box mode

 

@EXPORT

Export

Alias: EXP

Keywords:

/FI[LE]=<file-name>

result file name

/FO[RMAT]=<file-format>

DXF, AAMA, CADL, IGES, XML, NST, ALG, AXML

[/XS[CALE]=<X-scale>]

 

[/YS[CALE]=<Y-scale>]

 

[/NS[PLINE]={NO | YES}}]

Using splines and polylines

[/SP[ST]=<spline step>]

Step for spline line export (only if /NS=YES)

[/NA[RC]={NO | YES}]

Using arcs

[/ARCN[UM]=<Lines>]

Max no. of lines for arc (only if /NARC=YES)

[/ARCB[ULGE]=<bulge>]

Bulge for arc lines (only if /NARC=YES)

 

@PLOTTER

Plotting to file.

Alias: PLO

Keywords:

/FI[LE]=<file-name>

 

[/[USE]OCC={Y[ES] | N[O]}]

 

[/NA[ME]={<plotter name(case OCC)> | <plotter number(1-8)>}

 

/FO[RMAT]=<file-format>

DMPL, CYBCUT(Cybrid Cutter/Plotter), CYBPL(Cybrid Plotter), IOLS, HPGL, HP2(HPGL/2), HPTEC(HPGL PlotTec), HPGEN(HPGL Generic), HPLR(HPGL Laser), HP[GL]BAR( HPGL Bar Code, ARISTO (Aristomat Cutter), ZUND(Zund (PN, LC) Cutter), IEA, WILD(Wild Cutter/Plotter), WLDPL(Wild Plotter), EAST(Eastman Cutter), APGL(Gerber Plotter), AP700(AP 700 PLOTTER), MICRO(MicroJet Plotter), GERBER(Gerber Cutter), CEDGE(Cutting Edge), TAKA(Takaoka Cutter),         LECTRA(Lectra Flat Bed Plotter), LECFP(Lectra FlyPen), Mutoh, GERBCP(Gerber Cutter for Plotter, OptiJet(OptiJet Printer/Plotter), LECTCT(Lectra ISO Cut)

[/XS[CALE]=<X-scale>]

Scale Factor by X

[/YS[CALE]=<Y-scale>]

Scale Factor by Y

[/SC[ALE]=<type>] SPG(single page), MPG(multi page), FSC(fixed scale)

 

[/PGX=<Page size X>]

Page Size by X

[/PGY=<Page size Y>]

Page Size by Y

[/SIMP[LE[ST]][PAGE]]={Y[ES] | N[O]}]

Set Port View to Image Size - By Default - NO

[/SP[ST]=<spline step>]

Step for spline line plotting

[/ARCB[ULGE]=<bulge>]

Bulge for arc lines

[/NO[TE]=<{*C[LEAR] | *M[ARKERNAME] | <Note text>}]>]

 

[/NO[TE]PI[ECE]={Y[ES] | N[O]}]

Add Note to Piece Descriptions

[/FONT[FILE]=<font file name>]

File for Font ( for use non built-in font )

[/F[ONT]SIZE=<font size>]   

Default Font Size

[/BIF={Y[ES] | N[O]}]

Using built-in font for plotter

[/PEN[NUM]=<No.of pens>]

No.of heads

[/[MIN]LINE=<min line length for plotter>]

Min. Plot/Cut Line

[/MINCIRCLE[RAD]=<min circle radius for plotter>]

Minimal Circle Radius

[/GAP=<Gap after plotting length>]

Gap after Plotting

[/ONEP[AGE]={Y[ES] | N[O]}]

One Frame Only

[/CEN0={Y[ES] | N[O]}]

 (0, 0) in Frame Center

[/CENFLIP={Y[ES] | N[O]}]

Flip coordinates by (0, 0) center

[/MAN[FF]={Y[ES] | N[O]}]

Using manual Page Advance

[/OVER[LAP]={Y[ES] | N[O]}]

Plot Continuous

[/BORD[ER]={Y[ES] | N[O]}]

Marker Boundary

[/[AUTO]MOT[ION]={Y[ES] | N[O]}]

Order according tools (all internals on Marker first)

[/TSTSEGM={Y[ES] | N[O]}]

Remove plotting segments data in pieces with non-plotting segments before plotting

[/OPT={Y[ES] | N[O] | S[HARED]}]

Prepare Moving Optimization (Calculate Shared Lines)

[/OUTM[AN]={Y[ES] | N[O]}]

Using Output Manager   

[/COP[IES]=<No.of copies>]

No.of copies for Output Manager

[/ALS[TART]={Y[ES] | N[O]}]

Alert on Start in Output Manager

[/ALE[ND]={Y[ES] | N[O]}]

Alert on End in Output Manager

[/RME[ND]={Y[ES] | N[O]}]

Remove file on End in Output Manager

[/NET[WORK]={Y[ES] | N[O]}]    

Network Plotting

[/STAT[US]={Y[ES] | N[O]}]   

Plot Marker Header After the Marker

[/CR[LF]={Y[ES] | N[O]}]    

USE CR/LF in code

[/HPOPT[PAGESIZE]={Y[ES] | N[O]}]

Page Size optomization for HPGL/2 and HPGL PlotTec

[/LAST[FA]={Y[ES] | N[O]}]   

Frame Advance after the Last Frame

[/WHOLE[Pieces]={Y[ES] | N[O]}]

Plot/Cut Piece in One Frame

[/COL[ORS]={Y[ES] | N[O]}]

Pens (Tools) According to Sizes

[/OPTC[utOrder]={Y[ES] | N[O]}]

Optimize Plot/Cut Order

[/PLOTHS or PlotHeaderStatus = {Y[ES] | N[O]}]

Plot Marker Header Prior the Marker

[/PL[OT]EXT[ERN] = {Y[ES] | N[O]}]

Plot External Contour ( By Default - YES )

[/PL[OT]BUF[FER] = {Y[ES] | N[O]}]

Plot Buffer ( By Default - NO )

[/PLOTBL or PlotBumpLines = {Y[ES] | N[O]}]

Plot Bump Lines

[/PLOTS[plices]={Y[ES] | N[O]}]

Plot Splicing Marks

[/SPLSIZE=<value>]    

Splicing marker origin and size

[/PLOTR[ulers]={Y[ES] | N[O]}]

Plot X-Ruler

[/PLOTST[ripes]={Y[ES] | N[O]}]

Plot Stripe and Plaid Lines

[/M70={Y[ES] | N[O]}]    

Use initialization in file header (<M70>/<IN>...)

[/BITE or /BT = {Y[ES] | N[O]}]

Use Byte Offset

[/OFF[SET]=<value>]

Byte Offset Value. By Default 0.0

[/YOFF[SET]=<value>]

Y Offset Value. By Default 0.0

[/USEH[EAD]={Y[ES] | N[O]}]  

Use Custom Header

[/H[EAD]BYFR[AME]={Y[ES] | N[O]}]

Use Header by Frame

[/HEAD[ER]=<header>]    

Custom Header

[/USEF[OOT]={Y[ES] | N[O]}]  

Use Custom Footer

[/F[OOT]BYFR[AME]={Y[ES] | N[O]}]

Use Footer by Frame

[/FOOT[ER]=<footer>]     

Custom Footer

[/PFOVR or PlotFoldOvercut = <Length of overcut for folded pieces>]

Overcut Length

[/M19N[OTCH]={Slit | NSlit | All | None}]

M19 for Slit Notches / M19 for non Slit Notches

[/INCH={Y[ES] | N[O]}]  

Use Inch units

[/[USE]G70={Y[ES] | N[O]]

Use G70 in Inches Cutting

[/HPGLENG[LISH]={Y[ES] | N[O]]

HPGL English Unit

[/NODRAW={Y[ES] | N[O]}]

No Draw ( Cut Only )

[/BLO[CK]={ANP | MWB | MWS | COAB }]

Plot Blocks parameter - Default MWB

ALL pieces, Marker With Blocks, Marker With Selected Blocks Only, Only Pieces Outside of Block

[/OPS[TOP]={Y[ES] | N[O]}]   

OpStop Follows Stripe Adjust

   [/ONE[HEADER]LINE={Y[ES] | N[O]}]

One Line Marker Header

[/HpglWithoutDrill or HpglNoDrill={Y[ES] | N[O]}]

( by default = NO )

HpglDrillWithoutRadius Plotter ini parameter without UI

[/LIFT[PLUNGE]={Y[ES] | N[O]}]

Use Lift & Plunge

[/LIFT[PLUNGE]ANG[LE] = <angle>]

Lift & Plunge Angle in degrees

[/[USE]M31 = {Y[ES] | N[O]}]   

 Use M31 for Plot text

[/CUTDARTS[PLEATS] = {Y[ES] | N[O]}]

Cut darts and Pleats notches

[/DE[PLOT] = {A[LL] | N[O] | [S][P][C][D][Z][B][M]}

Plot piece-description fields all or no or defined only :

S - Style Name, P - Piece Name, C - Code Name, Z - Size name,

D - Description, B - Bundle Code, M - Material Name

 

@PRINT

Print Marker on default printer

Alias: PRI

Keywords:

[/FI[XED]={YES | NO}]

Print Marker with fixed scale. Default - NO - single page. (obsolete)

[/XS[CALE]=<X scale>]   

Default - 1.

[/YS[CALE]=<Y scale>]     

Default - 1.

[/HE[ADER]={YES | NO}]

Print Marker info header.   Default - YES.

[/EX[HEADER]={YES | NO}]

Print Marker info extended header. Default - NO.

[/BO[RDER]={YES | NO}]

Print Marker borders. Default - YES.

[/ST[RIPE]={YES | NO}]

Print stripe and plaid lines.  Default - NO.

[/NO[TE]={*C[LEAR] | *M[ARKERNAME] | <Note text>}]

The note to be printed.

[/MA[RKER]={YES | NO}]

Print the marker.   Default - YES.

[/PI[ECES]={YES | NO}]

Print the pieces.   Default - NO.

[/RE[PORT]={YES | NO}]

Print a report.   Default - NO.

[/COL[OR]={YES | NO}]  

Print in color mode.

[/CON[TINUOUS]={YES | NO}]

Print in continuous mode (for fixed scale). Default - No.

[/FO[RMAT]={SINGLE | MULTIPILE | FIXED}]

Format option. Default - single. (can not be used with /FIXED)

 

@CLEAR

Clears the currently opened marker table

Alias: CLE

 

@MARKER

Set marker table size and properties.

Alias: MRK

Keywords:

[/NA[ME]=<Marker name>]

 

[/LE[NGTH]=<length>]   

Marker dimensions

[/HE[IGHT]=<height>]

 

[/XO=<x-left>]   

Left Margin

[/XE=<x-right>]

Right Margin

[/YO=<y-bottom>]

Bottom Margin

[/YE=<y-top>]

Top Margin

[/PL[Y]=<No.of plies>]

Number of plies

[/MA[TERIAL]=<Material>]

Material

[/FV={NO | YES}]  

Marker full view mode

[/SX[STEP]=<x-step between vertical stripes>]

 

[/SY[STEP]=<y-step between horizontal stripes>]

 

[/SO[FF[SET]]X=<x offset for stripes>

 

[/SO[FF[SET]]Y=<y offset for stripes>

 

[/SA[DJ[UST]]={YES | NO}

 

[/LA[YOUT]={SI[NGLE] | TU[BULAR] | FA[CED] | FO[LDED]}

 

[/MU[LTIPLEMATERIALS]={Additional material}

There can be several parameters of this type. Causes /MA[TERIAL] to be ignored.

 

@GLOBAL

Set global pieces parameters.

Alias: GLO

Keywords:

[/ST[YLE]=<Style name>]

Key parameter used for the piece identification

[/SIZ[E]=<Size name>]

 

[/USESIZEKEY(or USK)]={Y[ES] | N[O]}

Use size name as key parameter used for the piece identification

[/NA[ME]=<Piece name>]

Key parameter used for the piece identification

[/NU[MBER]=<Piece index>]

The index of the piece. Could also be used as a key to identify the piece.

[/RT[YPE]=<Notch Type Restriction>]

T, V, I, L, U, P

[/RM[ODE]=<Mode Restriction>]

D[RAW], C[UT], P[UNCH], DR[ILL], ADR[ILL], N[ONE]

[/CO[DE]=<Piece code>]

 

[/TO[OL]=<Tool/Layer name for pieces external contour>]

 

[/HT[OOL]=<Tool/Layer name for piece holes>]

 

[/IT[OOL]=<Tool/Layer name for internal contours>]

 

[/NT[YPE]=<Notch Type>]

T, V, I, L, U, P

[/CT[IME]=<Notch Cutting Time>]

B[EFORE], I[NTIME], A[FTER]

[/NM[ODE]=<Notch Mode>]

D[RAW], C[UT], P[UNCH]

[/PM[ODE]=<Point Mode>]

D[RAW], C[UT], DR[ILL], ADR[ILL]

[/ND[EPTH]=<Notch Depth>]

 

[/NW[IDTH]=<Notch Width>]

 

[/BD[IAM]=<Button Diameter>]

 

[/SI[DE]=<Side label>]

L[EFT], R[IGHT], X[FLIP], Y[FLIP], LX, LY, RX, RY

[/D2M[ATCH]=<Type>]  

Converts Buttons to Match point. (Type: 0 - Any Button, 1 - Drill, 2 - Aux.Drill)

[/NF[IX]={ NO | YES }]

Clear leading numerical code from piece names.

[/GB[UF]=<Buffer size>]

 

[/GB[UF]I[NIT]={Y[ES] | N[O]}

Init Buffer. By Default - YES.

[/GB[UF]T[YPE]={A | C | U | D | L | R | UL | UR | DL | DR |   ULR | DLR | RUD | LUD }

Buffer Type. By Default - A ( Around ). The Around option is used in a case of negative buffer value.

[/GD[IR]=<Rotation allows>]  

1(None), 2(PI), 4(PI/2), 8(PI/4), 0(All enable)

[/GM[IR]=<Mirror allows>]

0(None), 1(Allow by X), 2(Allow by Y)

[/GT[ILT]=<Tilt value in degrees>]

 

[/QU[ANTITY]=<Quantity>]

 

[/MA[TERIAL]=<Material>]

 

 

@FLAW

Adds flaw area to the marker table.

Keywords:

/L[EFT]=<Value>

The coordinate of the left side of the flaw rectangle

/B[OTTOM]=<Value>

The coordinate of the bottom side of the flaw rectangle

/R[IGHT]=<Value>

The coordinate of the right side of the flaw rectangle

/T[OP]=<Value>

The coordinate of the top side of the flaw rectangle

 

Example:

@FLAW  /L=6 /B=25 /R=10 /T=100

Note that the coordinates refer to the zero at the bottom left of the marker table.

 

 

@TRANS

Transform Piece geometry.

Alias: TRA

Keywords:

[/ST[YLE]=<Style name>]

Key parameter used for the piece identification

[/SIZ[E]=<Size name>]

Key parameter used for the piece identification

[/NA[ME]=<Piece name>]

Key parameter used for the piece identification

[/CO[DE]=<Piece code>]

 

[/RO[TATE]=<Angle in degrees>]

 

[/FL[IP]={YES | NO}]

 

[/XS[CALE]=<Horizontal Scale factor>]

 

[/YS[CALE]=<Verticalal Scale factor>]

 

 

@NEST

AutoNesting (also works as Continue nesting).

Alias: NES

Note: Continue is not supported for the older algorithms Standard & Nest ++.

Keywords:

/AL[GORITHM]=<algorithm-type>

QUI[CK] (Standard with Quick), QUA[LITY] (Standard), TEX[TILE](Nest++), NES[TER], COM[PACT[ION]], MAT[CH](Match++), ANT(Nest++2), PRO(Nest++Pro), LEA[THER]

[/TI[ME]=<time>]

Time (minutes) for Nest++(TEX), Match++(MAT), External Nester(Nester), Nest++2(ANT), Nest++Pro(PRO)

[/EL | EFFLIM = <efficiency limit>]

Efficiency Limit in %, default - 100.0.

[/IT | IDLETIME = <idle time>]

Last idle time in minutes between found solutions, default - 0.0. Works for Nest++2, Nest++Pro.

[/BU[NDLES]]

Unify pieces orientation within bundles

[/BG(or BUNDLESGROUP)=Y[ES] | N[O]]

Nest coording to bundles.

[/BO(or BUNDLESOVERLAP)=L[ARGE] | M[EDIUM] | S[MALL]]

Nest bundles overlap.

[/UN[LIMIT]=Y[ES] | N[O]]  

Unlimited Marker X-size

[/RE[NEST]=Y[ES] | N[O]]  

Renest current pieces on marker.

[/IB(or IGNOREBUMP)=Y[ES] | N[O]]

Ignore bump line during nesting.

[/SM(or AUTOSAVEMARKERS)=<file name>]

Auto Save Markers

[/AF | /ALLOWFOLDED = { YES | NO }

Allow Folded on Both Side. (By Default - YES).

[/UQ | USEQUA | QUA | USEQUALITY | QUALITY = { YES | NO }]

Use Quality for AL=LEATHER (Default from .ini file or Yes)

[/OSC = { YES | NO | <Area> }]

Optimize Space for Cutting. Area: all pieces with equal or smaller area will be included in the process.

[/BLOCK=<Block Algorithm number>]

Works only with Nest++Pro. (Default from .ini file or No)

0 - Regular (default),

1 - Blocks First,

2 - Blocks Last,

3 - Blocks Only,

4 - No Blocks.

 

@BUMPLINEREMOVE

Removes bump lines

Alias: BUMPREM

Keywords:

/TYPE or /TY = { HO[RIZONTAL] | VE[RTICAL] | ALL }

  • The HORIZONTAL option should remove all horizontal bump lines available in current Marker file.

  • The VERTICAL option should remove all vertical bump lines available in current Marker file.

  • The ALL option should remove all bump lines in current Marker file, both vertical and horizontal.

 

@REPORT

Build Report in Excel format

Alias: REP

Keywords:

/FI[LE]=<file-name>  

Excel file name

[/TE[MPLATE]=<Template number>]

 

0 - Global Report (by current customization in Maker)

1 - Cost Calculation

2 - Check current Solution

3 - Time Calculations

 

Default - 0.

 

@REPORTW

Build Report using report writer functionality

Alias: REPW

Keywords:

 /TE[MPLATE=<template-file-name>

Path to the template file (mandatory).

/TY[PE]={PDF | XLSX | CSV}

Choose the report document type to be either .xlsx, .csv or .pdf (mandatory)

/OUT[PUT]=<file-name>

Output file name. (Optional)

If /OUT is missing - the report is generated inheriting current file name and location.

[/IN[PUT]]=<file-name>

Input Marker file name (Optional). Multiple /IN records should be available to generate aggregation report for multiple files.

If /IN is missing - current file is used.

 

@DISPLAY

Show/Hide Pieces attributes

Alias: DIS

Keywords:

[/DE[SC]={YES | NO | [S][P][C][D][Z][B][M]}]

View All Piece descriptions (S - Style Name, P - Piece Name, C - Code Name, Z - Size name, D - Description, B - Bundle Code, M - Material Name)

[/TE[XT]={YES | NO}]

View All Piece descriptions and Internal Text

[/TI[LT]={YES | NO}]

View Placed Piece Tilt Value

[/BU[FFER]={YES | NO}]

View Piece Buffer

[/IN[TERNAL]={YES | NO}]

View All Internals

[/DR[AW]={YES | NO}]

View Internals DRAW, SEW and QUALITY

[/CU[T]={YES | NO}]

View Internals CUT

[/DRILL={YES | NO}]

View Internals DRILL and AUXDRILL

[/BA[SELINE]={YES | NO}]

View Base Line

[/NO[TCH]={YES | NO}]

View Notches

[/BU[TTON]={YES | NO}]

View Buttons

 

@CHTOOL

Change tool command

Alias: CHT

Keywords:

/PM[ODE]

The new tool to be selected, can be one of:

/DR[ILL] for the drill tool, [ADR]ILL for the auxiliry drill, [NO]NE for none.

/MI[N] the minimal value of the range.

/MA[X] the maximal value of the range.

 

 The command replaces drills whose size is within the range [minimal value, maximal value).

For example:

@CHT /PM=DRILL /MIN=0.9 /MAX=1.2

would replace any drill or auxiliary drill where the size is smaller then 1.2 but equal or greater than 0.9

 

@SNAPSHOT

Create a snapshot command

Alias: SNAP

Keywords:

[/FO[RMAT]={PNG | SVG}]

The file format of the snapshot (default is PNG)

[/FI[LE]=<snapshot file name>]

The file name of the snapshot. (If missing the marker file name is used with the automatic extension.

[/EXT[ENSION]={YES | NO}]     

Add automatic file extension if none is sepcified (default true).

[/C[ROP]X=<max x (width) pixels>]

[/C[ROP]Y=<max y (height) pixels>]

Crop image size (for PNG only)

 

@GLOBALINTERNAL

Modify piece internals

Alias: GLOINT

Keywords:

 /RINT[ERNAL]={NO | BO | DPP | CONT | CIRC | LINEARCS}

The type of internals to be modified.

[/ST[YLE]=<style name>]

Handle only pieces from the specified style.

[/SIZ[E]=<size name>]

Handle only pieces of the specified size.

[/NA[ME]=<piece name>]

Handle only pieces of the specified name.

[/CO[DE]=<piece code>]

Handle only pieces of the specified code.

[/NU[MBER]=<The index of the piece>]

It can be used to limit the scope of the command to a single element by it's index. Can not be combined with /ST /SIZ /NA or /CO

[/RTY[PE]={T | V | I | L | U | P}]

The subtype of the notch to be modified.

[/RM[ODE]={D | DRAW | C | CUT | P | PUNCH | DR | DRILL | ADR | ADRILL | QUAL | QUALITY | SEW | NONE}]

Handle only internals of the specified mode

[/RTO[OL]=<layer name>]    

Handle only internals from the specified layer.

[/RTI[ME]={B | BEFORE | I | INTIME | A | AFTER}

Handle only internals pruduced at the specified time

[/RNOTCHLOC or /RNL={E | EXTERNAL | I | INTERNAL}]

Handle only internal/external notches.

[/NTO[OL]=<layer name>]    

Set the internal to be in specified layer.

[/NTY[PE]={T | V | I | L | U | P | CTL | CTC | CTB}]

Change the type of internal

[/NTI[ME]={B | BEFORE | I | INTIME | A | AFTER}]

Change the production time

[/NMO[DE]={D | DRAW | C | CUT | P | PUNCH | DR | DRILL | ADR | ADRILL | QUAL | QUALITY | SEW | NONE}]

Set the mode of the internal.

[/NAN[GLE]=<angle in degrees>]   

Change the angle of the internal

[/ND[EPTHRAD]=<depth>]   

Change the depth of the internal

[/NW[IDTH]=<width>]

Change the width of the internal

[/NTOPWIDTH or /NTW=<top width>]         

Change the top width of the internal.

[/RCT[YPE]={CLS | CLOSE | NCL | NCLOSE}  

Handle only internal contour Closed or Non-Closed.

[/NCT[YPE]={CLS | CLOSE | NCL | NCLOSE | H | HOLE}

Change the internal contour to Closed, to Non-Closed or to Hole.

[/MINSZ=<minimal size value>]   

Change only internals with size >= minimal size value

[/MAXSZ=<maximal size value>]   

Change only internals with size <= maximal size value    

 

@?

Continue batch process( Even after Error).

Keywords:

 [ comment ]

 

 

@PLACE

Place a piece ( or same pieces ) on the Marker

Alias: PLA

Keywords:

[/PI[ECE]=<piece name>]

by default first piece is used

[/SI[Z[E]]=<size name> or /SZ=<size name>]

by default first size is used

[/TP={O[NE] | A[LL} | B[UNDLES]}

place one instance (by default), all instances of the pieces or all instances from bundles of the piece.

[/FO[LD]={LF | RG | UP | DW | LU | RU | LD | RD | LEFT | RIGHT | DOWN}]

place with folding work for place one piece only ( if /TP=ONE or omitted )

LF=LEFT, RG=RIGHT, DW=DOWN, LU - Left-Up, RU - Right-Up, LD - Left-Down,

RD - Right-Down folding types.

 

@SUBSTITUTE

Piece Substitute

Alias: SUB

Keywords:

/FI[LE]=<source file name>

 

[/SE[AM]={I[NT] | E[XT] | C[UT] | S[EW] | B[OTH]}]

read option ( default BOTH ).

[/STY[LE]S[ET]=<style set name>]

style set (sub style) if use style set.

[/CUR[RENT]S[TYLE]=<current style name>]

by default first style

[/S[OURCE]NAME=<piece name>

piece for substitute in source file

[/T[ARGET]]NAME=<piece name>

place for substitute in current style

[/SSI[ZE]=<source size name>]

by default first size of the piece is used

[/SI[ZE]=<size name>]

by default first size of the piece is used

[/MIR[ROR]={Y[ES] | N[O]}]

Mirror in substitute ( default NO )

[/ROT[ATION]=<angle in grad>

Rotation in substitute ( default 0.0 )

[/DEL[ETEUNUSED]={Y[ES] | N[O]}]

Remove not used reading pieces (default YES).

 

@SPREADINGMACHINEREPORT

Create spreading Machine Report in Excel Format

Alias: SPR[EADING]MACH[INE]REP[ORT]

Keywords:

/FI[LE]=<file-name>  

Excel-file mame

[/C[UT]FI[LE] = <Cut file name>]

 

[/S[PR]FI[LE] = <Spreading Machine ASCII file name>]

 

 

@LEATHER

Open leather file (.pds)

Keywords:

/FI[LE] = <file-name>    

Leather file name file name (*.pds)

 

@ADJUSTDESCRIPTION

Adjust size and location of the description text

Alias: ADJ[UST]DESC[RIPTION]

Keywords:

[/MN[Sz]=<MINFONTSIZE>]   

Minimal Font Size

[/MX[Sz]=<MAXFONTSIZE>]  

Maximal Font Size

[/PAR[BASE[LINE]] = { YES | NO }

 Should piece description direction be set to be parallel to the baseline.

 

@OPTIMIZEORDER

Cut Plot Optimization

Alias: OTO

Keywords:

[/CCO or /CngCutOrd] = { YES | NO }

Change Cut Order

[/StartTop or ST]  = { YES | NO }

Start from the Top of the Marker

[/ChooseSP or CSP] = { YES | NO }

Choose (change) Start Point

[/ExtCutDir or ECD] = { OPT | CW | CCW }

External Contours Cut Direction: Optimize | Clockwise | Counter-Clockwise |

By default, cut direction remains unchanged.

[/UseFrame or UF] = { YES | NO }

Use Frame (pages)

[/FrameX or FX] = <float value>

X frame size

[/FrameY or FY] = <float value>

Y frame size

[/OptiLimitFrom or OLF] = <int value>

Optimization Limit from instance number

[/OptiLimitTo or OLT] = <int value>

Optimization Limit to instance number

[/AutoDetectSharedLine or /ADSL]  = { YES | NO }

Auto Detecting Shared Lines

[/MaxAngle or /MA] = <float value>

Max Shared Angle

[/MaxDis or /MD] = <float value>

Max Shared Distance

[/MinLen or /ML] = <float value>

Min Shared Length

[/NoCutDown or /NCD] = { YES | NO }

Do not Cut near Marker Down Limit

[/NoCutUp or /NCU] = { YES | NO }

Do not Cut near Marker Up Limit

[/NoCutLeft or /NCL] = { YES | NO }

Do not Cut near Marker Left Limit

[/NoCutRight or /NCR] = { YES | NO }

Do not Cut near Marker Down Limit

 

@BUMPLINE

Add Bump Line

Alias: BUMP

Keywords:

/TYPE or /TY = { HO[RIZONTAL] | VE[RTICAL] | RIGHTEDGE or RE }

 

/LO[CATION] = <float value>]

Location

 

@XEXIT

Stop the Batch, Remove Batch file and close Marker.

Alias: XEX

 

@XOE

Stop the Batch on Error

 

 See also: